Careers at Resurgence Small Engine Inc.

If you are interested in a career at Resurgence Small Engine Inc., review the positions listed below. Please apply for the level for which you are currently qualified for all the tasks & skills. One of the benefits of working at Resurgence Small Engine Inc. is the opportunity for training & continual skill building.

We are currently hiring for Tech 3, Level 1.
Apply through Indeed

Tasks

  • Inspect/top off fluids
  • Change engine oil & filters
  • Change differential oil
  • Change air filters
  • Change tires and install tubes
  • Remove\reinstall basic belts, friction disks, pressure washer pumps
  • Inspect for damaged mower blades, sharpen blades
  • Lubricate moving parts (bushings/bearings/u-joints, etc.)
  • Drain fluids and prepare units for recycling
  • Removing and installing plastics
  • Painting shop equipment
  • Change batteries
  • Maintain organization and cleanliness in shop and parts warehouse
  • Maintain shop yard

Skills

  • Diagnose tires
  • Assess batteries via battery tester
  • Properly use hand tools and pneumatic tools
  • Properly use hoist

Tasks

  • All Tasks of Tech 1, Level 1
  • Full OPE and Powersports Inspections
  • Repair tires and tubes
  • Replace lawn tractor and snowmachine belts
  • Level lawn tractor decks
  • Repair OPE recoil
  • Removal and installation of OPE engines
  • Dismantle parts units
  • Compression/ignition test OPE
  • Chainsaw 2 stroke Vacuum/pressure test
  • Installing cables
  • Replace brake pads, brake shoes
  • Replace Brake lines, Master cylinder
  • Replace CV boots
  • Pressing bearings\ball joints\U-joints
  • Setting wheel alignment
  • Installation\removal drive chains
  • Adjusting drive chain tension
  • Adjusting track tension
  • Adjust suspensions
  • Sharpen Chainsaw Chains
  • Assist clients to load and unload machines

Skills

  • All skills of Tech1, Level 1
  • Use cutting disks on angle grinder
  • Ability to use press
  • Measure chainsaw chains
  • Can use slide hammer/bearing puller/3 jaw puller

Tasks

  • All Tasks of Tech 1, Level 2
  • Install and remove all carburetors
  • Repair Autochoke systems
  • Drill and Replace Broken Bolts
  • Valve cover Gaskets
  • Replace Ignition coils on OPE
  • Replace petcocks
  • Fitting plow Mounts\Plows
  • Make Chainsaw Chains
  • Change Snowmachine Tracks (not including chaincase)
  • Snowmachine Track Slides
  • Remove motorcycle wheels

Skills

  • All skills of Tech 1, Level 2
  • Use snowmachine clutch pullers
  • Final inspections of outgoing units
  • Greet clients and explain service process and repairs

Tasks

  • All Tasks of Tech 2, Level 1
  • Valve adjustments OPE
  • Set governers
  • OPE carburetor rebuilds
  • Leakdown test OPE
  • Compression\ignition test Powersports
  • Powersports 2 stroke Vacuum/pressure test
  • Clutch alignments
  • Removal and installation of snowmachine engines
  • Change Snowmachine Tracks (including chaincase)

Skills

  • All skills of Tech 2, Level 1
  • Read and interpret parts schematics
  • Use Valve grinder
  • Use flywheel pullers
  • Basic welding Flux Core\Mig

Tasks

  • All tasks of Tech 2, Level 2
  • Full Engine Diagnostics and assessment on OPE
  • All Valve adjustments
  • Removal and installation of the atv\motorcycle\other powersports engines
  • Balance and true motorcycle wheels
  • Clutch Side 2 stroke crankshaft seals
  • Outboard impellers
  • Inspect,Tag and label parts from dismantled units

Skills

  • All skills of Tech 2, Level 2
  • Use Dial Indicator and Dial Caliper
  • 97% success rate on non-electrical OPE repair
Full Job Description for Tech 3, Level 1.

Tasks

  • All tasks of Tech 2, Level 3
  • Full rebuild of OPE engines
  • Repair top end powersports engines
  • Repair (outer)lower-end of powersports engines
  • Powersports carburetor rebuilds
  • Rebuilding Forks
  • Rework differentials
  • Hone cylinders
  • Clean Nikasil cylinders
  • Clutch assessment\rebuild

Skills

  • All skills of Tech 2, Level 3
  • Basic electrical understanding(switches, resistance, relay, diode)
  • Can use bore gauge, micrometer, dial indicator and dial caliper
  • Properly use flywheel pullers, clutch pullers, blind bearing pullers and bearing splitters
  • Use soda blasting cabinet
  • All parts removed from a project must go back in correctly and in the correct order

Tasks

  • All tasks of Tech 3, Level 1
  • Full rebuild Transmissions
  • Full Rebuild of Powersports Engines
  • Fabricate shop tools

Skills

  • All skills of Tech 3, Level 1
  • Understand OPE electrical scematics
  • Has at least a motorcycle permit
  • Good welding at Flux Core\MIG or TIG
  • 97% success rate on all units repair

Tasks

  • All tasks of Tech 3, Level 2
  • All Tasks of Techs 1,2,3
  • Maintain shop tools and equipment
  • Electrical diagnostics (CDI sytems, ECU systems, EFI)
  • Train lower level techs
  • Service adviser role
  • Calculating time for repairs
  • Identifying, tagging, and photo parts for sale

Skills

  • All skills of Tech 3, Level 2
  • Can use scantools, multimeter and oscilloscope
  • Read and interpret powersports electrical schematics
  • Find or design needed shop tools
  • Have Motorcycle license
  • Supervisory training